NSE7_LED-7.0 Free Exam Questions and Answers PDF Updated on Dec-2023
Latest NSE7_LED-7.0 Exam Dumps Recently Updated 40 Questions
NEW QUESTION # 19
Which EAP method requires the use of a digital certificate on both the server end and the client end?
- A. EAP-TTLS
- B. EAP-GTC
- C. PEAP
- D. EAP-TLS
Answer: D
Explanation:
Explanation
According to the FortiGate Administration Guide, "EAP-TLS is the most secure EAP method. It requires a digital certificate on both the server end and the client end. The server and client authenticate each other using their certificates." Therefore, option D is true because it describes the EAP method that requires the use of a digital certificate on both the server end and the client end. Option A is false because EAP-TTLS only requires a digital certificate on the server end, not the client end. Option B is false because PEAP also only requires a digital certificate on the server end, not the client end. Option C is false because EAP-GTC does not require a digital certificate on either the server end or the client end.
NEW QUESTION # 20
Refer to the exhibit
A device connected to port2 on FortiSwitch cannot access the network The port is assigned a security policy to enforce 802 1X authentication While troubleshooting the issue, the administrator obtains the debug output shown in the exhibit Which two scenarios are likely to cause this issue? (Choose two.)
- A. The device has been quarantined for 3600 seconds.
- B. The device is not configured for 802 IX authentication.
- C. The device has been assigned the guest VLAN
- D. The device does not support 802 1X authentication
Answer: B,D
Explanation:
Explanation
According to the exhibit, the debug output shows that the device connected to port2 on FortiSwitch is sending an EAPOL-Start message, which is the first step of the 802.1X authentication process. However, the output also shows that the device is not sending any EAP-Response messages, which are required to complete the authentication process. Therefore, option A is true because the device is not configured for 802.1X authentication, which means that it does not have the correct credentials or settings to authenticate with the RADIUS server. Option D is also true because the device does not support 802.1X authentication, which means that it does not have the capability or software to perform 802.1X authentication. Option B is false because the device has not been quarantined for 3600 seconds, but rather has a session timeout of 3600 seconds, which is the default value for 802.1X sessions. Option C is false because the device has not been assigned the guest VLAN, but rather has been assigned the default VLAN, which is VLAN 1.
NEW QUESTION # 21
When you configure a FortiAP wireless interface for auto TX power control which statement describes how it configures its transmission power"?
- A. Every 30 seconds FortiGate measures the signal strength of the weakest associated client The AP will then configure its radio power to match the detected signal strength of the client
- B. Every 30 seconds FortiGate measures the signal strength of adjacent FortiAP interfaces It will adjust the adjacent AP power to be detectable at -70 dBm
- C. Every 30 seconds the AP will measure the signal strength of the AP using the client The AP will adjust its signal strength up or down until the AP signal is detected at -70 dBm
- D. Every 30 seconds FortiGate measures the signal strength of adjacent AP interfaces It will adjust its own AP power to match the adjacent AP signal strength
Answer: C
Explanation:
Explanation
According to the FortiAP Configuration Guide1, "Auto TX power control allows the AP to adjust its transmit power based on the signal strength of the client. The AP will measure the signal strength of the client every 30 seconds and adjust its transmit power up or down until the client signal is detected at -70 dBm." Therefore, option A is true because it describes how the FortiAP wireless interface configures its transmission power when auto TX power control is enabled. Option B is false because FortiGate does not measure the signal strength of adjacent AP interfaces, but rather the FortiAP does. Option C is false because FortiGate does not adjust the adjacent AP power, but rather the FortiAP adjusts its own power. Option D is false becauseFortiGate does not measure the signal strength of the weakest associated client, but rather the FortiAP does.
NEW QUESTION # 22
You are investigating a report of poor wireless performance in a network that you manage. The issue is related to an AP interface in the 5 GHz range You are monitoring the channel utilization over time.
What is the recommended maximum utilization value that an interface should not exceed?
- A. 85%
- B. 75%
- C. 95%
- D. 65%
Answer: D
Explanation:
Explanation
According to the FortiAP Configuration Guide, "Channel utilization measures how busy a channel is over a given period of time. It includes both Wi-Fi and non-Wi-Fi interference sources. A high channel utilization indicates a congested channel and can result in poor wireless performance. The recommended maximum utilization value that an interface should not exceed is 65%." Therefore, option D is true because it gives the recommended maximum utilization value for an interface in the 5 GHz range. Options A, B, and C are false because they give higher utilization values that can cause poor wireless performance.
https://docs.fortinet.com/document/fortiap/7.0.0/configuration-guide/734537/wireless-radio-settings#channel-uti
NEW QUESTION # 23
Refer to the exhibit.
Examine the FortiGate user group configuration and the Windows AD LDAP group membership information shown in the exhibit FortiGate is configured to authenticate SSL VPN users against Windows AD using LDAP The administrator configured the SSL VPN user group for SSL VPN users However the administrator noticed that both the student and j smith users can connect to SSL VPN Which change can the administrator make on FortiGate to restrict the SSL VPN service to the student user only?
- A. In the SSL VPN user group configuration, change Name to cn=sslvpn, CN=users, DC=trainingAD, Detraining, DC-lab.
- B. In the SSL VPN user group configuration set Group Name to ::;=Domain users.CN-Users/DC=trainingAD, DC-training, DC=lab.
- C. In the SSL VPN user group configuration change Type to Fortinet Single Sign-On (FSSO)
- D. In the SSL VPN user group configuration set Group Nam to CN-SSLVPN, CN="users, DC-trainingAD, DC-training, DC-lab
Answer: D
Explanation:
Explanation
According to the FortiGate Administration Guide, "The Group Name is the name of the LDAP group that you want to use for authentication. The name must match exactly the name of the LDAP group on the LDAP server." Therefore, option A is true because it will set the Group Name to match the LDAP group that contains only the student user. Option B is false because changing the Name will not affect the authentication process, as it is only a local identifier for the user group on FortiGate. Option C is false because setting the Group Name to Domain Users will include all users in the domain, not just the student user. Option D is false because changing the Type to FSSO will require a different configuration method and will not solve the problem.
NEW QUESTION # 24
What is the purpose of enabling Windows Active Directory Domain Authentication on FortiAuthenticator?
- A. It enables FortiAuthenticator to import users from Windows AD
- B. It enables FortiAuthenticator to use a Windows CA certificate when authenticating RADIUS users
- C. It enables FortiAuthenticator to use Windows administrator credentials to perform an LDAP lookup for a user search
- D. It enables FortiAuthenticator to register itself as a Windows trusted device to proxy authentication using Kerberos
Answer: D
Explanation:
Explanation
According to the FortiAuthenticator Administration Guide2, "Windows Active Directory domain authentication enables FortiAuthenticator to join a Windows Active Directory domain as a machine entity and proxy authentication requests using Kerberos." Therefore, option D is true because it describes the purpose of enabling Windows Active Directory domain authentication on FortiAuthenticator. Option A is false because FortiAuthenticator does not need Windows administrator credentials to perform an LDAP lookup for a user search. Option B is false because FortiAuthenticator does not use a Windows CA certificate when authenticating RADIUS users, but rather its own CA certificate. Option C is false because FortiAuthenticator does not import users from Windows AD, but rather synchronizes them using LDAP or FSSO.
NEW QUESTION # 25
Refer to the exhibit.
Examine the IPsec VPN phase 1 configuration shown in theexhibit
An administrator wants to use certificate-based authentication for an IPsec VPN user Which three configuration changes must you make on FortiGate to perform certificate-based authentication for the IPsec VPN user? (Choose three)
- A. Enable XAUTH on the IPsec VPN tunnel
- B. Import the CA that signed the user certificate
- C. In the IKE section of the IPsec VPN tunnel in the Mode field select Main (ID protection)
- D. In the Authentication section of the IPsec VPN tunnel in the Method drop-down list select Signature and then select the certificate that FortiGate will use for IPsec VPN
- E. Create a PKI user for the IPsec VPN user, and then configure the IPsec VPN tunnel to accept the PKI user as peer certificate
Answer: A,B,D
Explanation:
Explanation
According to the FortiGate Administration Guide, "To use certificate-based authentication, you must configure the following settings on both peers: Select Signature as the authentication method and select a certificate to use for authentication. Import the CA certificate that issued the peer's certificate. Enable XAUTH on the phase 1 configuration." Therefore, options B, D, and E are true because they describe the configuration changes that must be made on FortiGate to perform certificate-based authentication for the IPsec VPN user.
Option A is false because creating a PKI user for the IPsec VPN user is not required, as the user certificate can be verified by the CA certificate. Option C is false because changing the IKE mode to Main (ID protection) is not required, as the IKE mode can be either Main or Aggressive for certificate-based authentication.
NEW QUESTION # 26
Which CLI command should an administrator use to view the certificate verification process in real time?
- A. diagnose debug application radiusd -1
- B. diagnose debug application fnbamd -1
- C. diagnose debug application authd -1
- D. diagnose debug application foauthd -1
Answer: D
Explanation:
Explanation
According to the FortiOS CLI Reference Guide, "The diagnose debug application foauthd command enables debugging of certificate verification process in real time." Therefore, option A is true because it describes the CLI command that an administrator should use to view the certificate verification process in real time. Option B is false because diagnose debug application radiusd -1 enables debugging of RADIUS authentication process, not certificate verification process. Option C is false because diagnose debug application authd -1 enables debugging of authentication daemon process, not certificate verification process. Option D is false because diagnose debug application fnbamd -1 enables debugging of FSSO daemon process, not certificate verification process.
NEW QUESTION # 27
Refer to the exhibit.
By default FortiOS creates the following DHCP server scope for the FortiLink interface as shown in the exhibit What is the objective of the vci-string setting?
- A. To restrict the IP address assignment to devices that have FortiSwitch or FortiExtender as their hostname
- B. To reserve IP addresses for FortiSwitch and FortiExtender devices
- C. To ignore DHCP requests coming from FortiSwitch and FortiExtender devices
- D. To restrict the IP address assignment to FortiSwitch and FortiExtender devices
Answer: D
Explanation:
Explanation
According to the exhibit, the DHCP server scope for the FortiLink interface has a vci-string setting with the value "Cisco AP c2700". This setting is used to match the vendor class identifier (VCI) of the DHCP clients that request an IP address from the DHCP server. The VCI is a text string that uniquely identifies a type of vendor device. Therefore, option C is true because the vci-string setting restricts the IP address assignment to FortiSwitch and FortiExtender devices, which use the VCI "Cisco AP c2700". Option A is false because the vci-string setting does not ignore DHCP requests coming from FortiSwitch and FortiExtender devices, but rather accepts them. Option B is false because the vci-string setting does not reserve IP addresses for FortiSwitch and FortiExtender devices, but rather assigns them dynamically. Option D is false because the vci-string setting does not restrict the IP address assignment to devices that have FortiSwitch or FortiExtender as their hostname, but rather to devices that have "Cisco AP c2700" as their VCI.
NEW QUESTION # 28
Refer to the exhibit.
Examine the FortiGate configuration FortiAnalyzer logs and FortiGate widget shown in the exhibit An administrator is testing the Security Fabric quarantine automation The administrator added FortiAnalyzer to the Security Fabric and configured an automation stitch to automatically quarantine compromised devices The test device (::.:.:.!) s connected to a managed Fort Switch dev :e After trying to access a malicious website from the test device, the administrator verifies that FortiAnalyzer has a log (or the test connection However the device is not getting quarantined by FortiGate as shown in the quarantine widget Which two scenarios are likely to cause this issue? (Choose two)
- A. The device does not have FortiClient installed
- B. FortiAnalyzer does not consider the malicious website an indicator of compromise (IOC)
- C. FortiAnalyzer does not have a valid threat detection services license
- D. The web filtering rating service is not working
Answer: B,C
Explanation:
Explanation
According to the exhibits, the administrator has configured an automation stitch to automatically quarantine compromised devices based on FortiAnalyzer's threat detection services. However, according to the FortiAnalyzer logs, the test device is not detected as compromised by FortiAnalyzer, even though it tried to access a malicious website. Therefore, option B is true because FortiAnalyzer does not have a valid threat detection services license, which is required to enable the threat detection services feature. Option D is also true because FortiAnalyzer does not consider the malicious website an indicator of compromise (IOC), which is a criterion for identifying compromised devices. Option A is false because the web filtering rating service is working, as shown by the log entry that indicates that the test device accessed a URL with a category of
"Malicious Websites". Option C is false because the device does not need to have FortiClient installed to be quarantined by FortiGate, as long as it is connected to a managed FortiSwitch device.
NEW QUESTION # 29
Where can FortiGate learn the FortiManager IP address or FQDN for zero-touch provisioning'?
- A. From a DHCP server using options 240 and 241
- B. From a DNS server using A or AAAA records
- C. From an LDAP server using a simple bind operation
- D. From a TFTP server
Answer: B
Explanation:
Explanation
According to the FortiGate Administration Guide, "FortiGate can learn the FortiManager IP address or FQDN for zero-touch provisioning from a DNS server using A or AAAA records. The DNS server must be configured to resolve the hostname fortimanager.fortinet.com to the IP address or FQDN of the FortiManager device." Therefore, option D is true because it describes the method for FortiGate to learn the FortiManager IP address or FQDN for zero-touch provisioning. Option A is false because LDAP is not used for zero-touch provisioning. Option B is false because TFTP is not used for zero-touch provisioning. Option C is false because DHCP options 240 and 241 are not used for zero-touch provisioning.
NEW QUESTION # 30
Refer to the exhibit.
Examine the RADIUS server configuration shown in the exhibit
An administrator has configured a RADIUS server on FortiGate that points to FortiAuthenticator FortiAuthenticator is acting as an authentication proxy and is configured to relay all authentication requests to a remote Windows AD server using LDAP While testing the configuration the administrator noticed that the diagnosetest authserver command worked with PAP, however authentication requests failed when using MSCHAP2 Which two solutions can the administrator implement to get MSCHAP2 authentication to work'' (Choose two.)
- A. On FortiAuthenticator enable Windows Active Directory Domain Authentication to add FortiAuthenticator to the Windows domain
- B. On FortiGate update the Secret setting on the RADIUS server
- C. On FortiGate configure the NAS IP setting on the RADIUS
server - D. On FortiAuthenticator change the back-end authentication server from LDAP to RADIUS
Answer: A,D
Explanation:
Explanation
According to the exhibit, the RADIUS server configuration on FortiGate points to FortiAuthenticator, which is acting as an authentication proxy and is configured to relay all authentication requests to a remote Windows AD server using LDAP. However, LDAP does not support MSCHAP2 authentication, which is required for RADIUS. Therefore, option A is true because on FortiAuthenticator, enabling Windows Active Directory Domain Authentication will add FortiAuthenticator to the Windows domain and allow it to use MSCHAP2 authentication with the AD server. Option C is also true because on FortiAuthenticator, changing the back-end authentication server from LDAP to RADIUS will allow it to use MSCHAP2 authentication with the AD server. Option B is false because on FortiGate, configuring the NAS IP setting on the RADIUS server will not affect the MSCHAP2 authentication, but rather the source IP address of the RADIUS packets. Option D is false because on FortiGate, updating the Secret setting on the RADIUS server will not affect the MSCHAP2 authentication, but rather the shared secret between FortiGate and FortiAuthenticator.
NEW QUESTION # 31
Refer to the exhibit
Examine the FortiGate RSSO configuration shown in the exhibit
FortiGate is configured to receive RADIUS accounting messages on port3 to authenticate RSSO users The users are located behind port3 and the internet link is connected to port1 FortiGate is processing incoming RADIUS accounting messages successfully and RSSO users are getting associated with the RSSO Group user group However all the users are able to access the internet, and the administrator wants to restrict internet access to RSSO users only Which configuration change should the administrator make to fix the problem?
- A. Change the RADIUS Attribute Value selling to match the name of the RADIUS attribute containing the group membership information of the RSSO users
- B. Enable Security Fabric Connection on port3
- C. Add RSSO Group to the firewall policy
- D. Create a second firewall policy from port3 lo port1 and select the target destination subnets
Answer: C
Explanation:
Explanation
According to the exhibit, the firewall policy from port3 to port1 has no user group specified, which means that it allows all users to access the internet. Therefore, option B is true because adding RSSO Group to the firewall policy will restrict internet access to RSSO users only. Option A is false because changing the RADIUS Attribute Value setting will not affect the firewall policy, but rather the RSSO user group membership. Option C is false because enabling Security Fabric Connection on port3 will not affect the firewall policy, but rather the communication between FortiGate and other Security Fabric devices. Option D is false because creating a second firewall policy from port3 to port1 will not affect the existing firewall policy, but rather create a redundant or conflicting policy.
NEW QUESTION # 32
Refer to the exhibits.
Exhibit.
Examine the troubleshooting outputs shown in the exhibits
Users have been reporting issues with the speed of their wireless connection in a particular part of the wireless network The interface that is having issues is the 2 4 GHz interface that is currently configured on channel 6 The administrator of the wireless network has investigated and surveyed the local RF environment using the tools available at the AP and FortiGate Which configuration would improve the wireless connection?
- A. Change the AP 2 4 GHz channel to 11
- B. Change the AP 2 4 GHz channel to 9.
- C. Change the AP 2 4 GHz channel to 13.
- D. Change the AP 2 4 GHz channel to 1.
Answer: D
Explanation:
Explanation
According to the exhibits, the AP 2.4 GHz interface is currently configured on channel 6, which is overlapping with other nearby APs on channels 4 and 8. This can cause interference and reduce the wireless performance.
Therefore, changing the AP 2.4 GHz channel to 1 would improve the wireless connection, as it would avoid the overlapping channels and use a non-overlapping channel instead. Option A is false because changing the AP 2.4 GHz channel to 11 would still overlap with other nearby APs on channels 9 and 13. Option C is false because changing the AP 2.4 GHz channel to 9 would still overlap with other nearby APs on channels 6, 8, and 11. Option D is false because changing the AP 2.4 GHz channel to 13 would still overlap with other nearby APs on channels 9 and 11.
NEW QUESTION # 33
Which FortiSwitch VLANs are automatically created on FortGate when the first FortiSwitch device is discovered1?
- A. access, quarantine, rspan. voice, video, and onboarding
- B. fortilink. quarantine erspan voice video and onboarding
- C. default quarantine, rspan voice video onboarding and nac_segment
- D. default quarantine rspan voice video and nac_segment
Answer: B
Explanation:
Explanation
According to the FortiGate Administration Guide, "When you add a FortiSwitch device to the Security Fabric, FortiGate automatically creates the following VLANs on theFortiSwitch device: fortilink, quarantine, erspan, voice, video, and onboarding." Therefore, option D is true because it lists the FortiSwitch VLANs that are automatically created on FortiGate when the first FortiSwitch device is discovered. Option A is false because default and nac_segment are not among the automatically created VLANs. Option B is false because access and rspan are not among the automatically created VLANs. Option C is false because default and nac_segment are not among the automatically created VLANs.
NEW QUESTION # 34
An administrator is testing the connectivity for a new VLAN The devices in the VLAN are connected to a FortiSwitch device that is managed by FortiGate Quarantine is disabled on FortiGate While testing the administrator noticed that devices can ping FortiGate and FortiGate can ping the devices The administrator also noticed that inter-VLAN communication works However intra-VLAN communication does not work Which scenario is likely to cause this issue?
- A. The native VLAN configured on the ports is incorrect
- B. The FortiSwitch MAC address table is missing entries
- C. The FortiGate ARP table is missing entries
- D. Access VLAN is enabled on the VLAN
Answer: B
Explanation:
Explanation
According to the scenario, the devices in the VLAN are connected to a FortiSwitch device that is managed by FortiGate. Quarantine is disabled on FortiGate, which means that the devices are not blocked by any security policy. The devices can ping FortiGate and FortiGate can ping the devices, which means that the IP connectivity is working. Inter-VLAN communication works, which means that the routing between VLANs is working. However, intra-VLAN communication does not work, which means that the switching within the VLAN is not working. Therefore, option C is true because the FortiSwitch MAC address table is missing entries, which means that the FortiSwitch does not know how to forward frames to the destination MAC addresses within the VLAN. Option A is false because access VLAN is enabled on the VLAN, which means that the VLAN ID is added to the frames on ingress and removed on egress. This does not affect intra-VLAN communication. Option B is false because the native VLAN configured on the ports is incorrect, which means that the frames on the native VLAN are not tagged with a VLAN ID. This does not affect intra-VLAN communication. Option D is false because the FortiGate ARP table is missing entries, which means that FortiGate does not know how to map IP addresses to MAC addresses. This does not affect intra-VLAN communication.
NEW QUESTION # 35
......
Fortinet NSE7_LED-7.0 Real 2023 Braindumps Mock Exam Dumps: https://actualtests.crampdf.com/NSE7_LED-7.0-exam-prep-dumps.html